A high-performance wax used by WCT athletes including Kelly Slater!

This exquisite product is handmade in Brazil using a top-secret recipe!

"Softest from top to bottom"
◆ "COLD" Midwinter (Water temperature: up to 13°C) Gloves and head cap
◆『COOL』Winter (Water temperature 13~18℃) Boots, Semi-dry
◆『SUMMER COOL』Spring/Autumn (Water temperature 17~21℃) 5~3mm full suit
◆ "WARM" Summer (water temperature 20-25℃) Seagull, Spring
◆ "TROPICAL" Midsummer (water temperature 24℃ and above) Tupperware, trunks
◆『BASE』All-season primer (can be used in all water temperatures)

▼NEW! "SUMMER COOL"

A new product from "FU WAX" has been released!
"FU WAX" had a slight difference in hardness between the two types, COOL and WARM, so after receiving feedback from team riders and FU WAXERS (heavy users) who wanted something with an intermediate hardness, FUAD launched "SUMMER COOL."

It can be used mainly in two seasons, spring and autumn, when the water temperature is between COOL and WARM.
In addition, WARM is also effective in the mornings and evenings of summer when the outside air and water temperatures are low and the paint is hard and difficult to apply, or when the wind blows in summer and the water temperature drops, causing a difference between the outside air temperature and the water temperature.

It is designed for situations where it is soft in COOL and hard in WARM.
The introduction of this "SUMMER COOL" allows for more precise adjustments to water temperatures, providing the strongest 3D grip for professionals.

▼BASE WAX
Apply this FU WAX base coat wax slowly, applying thin, overlapping layers.
Do not press the wax onto the board or apply it in a fast motion.
Once complete, apply a thin layer of FU WAX TOP COAT wax.

▼TOP COAT WAX
Be sure to apply a sufficient amount of base wax before using this as a top coat wax.
Do not place in a high temperature location as the wax may melt.
For long-lasting results, reapply immediately before each surfing session.
This is not a food product. Please be careful when storing it and keep it out of the reach of children.

FU WAX is effective enough when applied thinly as a top coat.
If you apply the wax evenly to the board and stop when thin, thread-like wax appears, you can use it more times without wasting too much.

Smooth out the wax and apply several thin coats until threads appear.
Just a thin coat of "FU WAX" is enough to be effective.
WCT players are captivated by this product and everyone agrees that once they start using it, they will never be able to use any other manufacturer's grip. Be sure to try out the amazing grip it offers.

▼ For more detailed information, please see our 24 's blog here .

↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓

" WAX like a suction cup that captivates WCT players "

I 『 FUAD　MANSUR is the only person who can make FU WAX .

You can see footage of Dane Reynolds using " FU WAX ."

"No one will believe it at first, but you should try it," Kolohe said.

 Check out the wonderful reviews from people who have actually used " FU WAX ".

While teaching his son how to make it, he sneaks into the secret " FU WAX " CA factory!

" FU WAX " introduces reports and photos from around the world.

We'll introduce you to some surprising ways to store and use FU WAX !



What makes it so different? It sticks to your surfboard like a suction cup, increasing your grip. It's so different you'll never want to use your old wax again. Give it a try! Its performance is unmatched by any other wax. Anyone can improve their surfing and gain confidence with just this one wax. By applying it flat against the board, you won't waste too much, allowing for more use (approximately 10-15 coats). Unlike other manufacturers, there's no need to apply it thickly or scrub it against corners. We recommend COOL for 3mm full suits, gloves, and boots , and COLD for head cap water temperatures .